Showing results: 1516 - 1530 of 2617 items found.
-
COMBI519 -
HT Italia Srl
COMBI519 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
COMBI521 -
HT Italia Srl
COMBI521 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
EASYTEST -
HT Italia Srl
EASYTEST carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Vacuum Interrupters, Inc.
Until now, the accepted field service test for vacuum interrupters has been a simple Go/No-Go test performed with an AC high potential test. Today, testing with our Magnetic Atmospheric Condition (MAC) test sets can prevent unnecessary damage to your circuit breakers and contactors by predicting the usable life of the vacuum interrupter.
-
IPMDS40 -
Technology Research Corp.
- Intelligent Power Management System- 9 - 20 Amp Single Outlets- Automatic Single Phase Load Balancing- Automatic Load Shedding based on priority rating- 40 Amp Mil Spec Input and Output Connector- Easy Access Circuit Breakers- Phase Over Current Protection- Low Voltage Warning- Built In Press to Test
-
SG5002\SG5003\SG5008 \SG5009 -
Shanghai Jiuzhi Electric Co., Ltd.
The SG5002 \ SG5003 \ SG5008 \ SG5009 high current resistance meters are special designed for high performance measurement of high inductance, low value resistances such as transformer windings, motors, breakers, switchgear etc. Unlike normal resistance meters these instruments have a built-in high-speed discharge circuits for safe discharge of the stored energy in a measured inductance.
-
DU-9001 -
Delta United Instrument Co., Ltd.
The 10 capacitor - LCC/DZ/R in order to automatically scan test improve the test reliability and test efficiencyEach test channel can be opened / short circuit return to zero with high precision.Wide range scan box can be used to test 3mm~35mm 10 capacitorsSuitable for high voltage capacitance test, 450V330uF 10 capacitors can be smooth test
-
HDYZ -
HD Power Test Equipment Co.ltd
HDYZ Transformer on-load tap changer Tester is a unique moving part that is connected with the circuit of the transformer, It is essential to test the on-load tap changer of action sequence and switching time.HDYZ Transformer On-load Tap Changer Tester is mainly applied to measure the transient waveform, transient time, transient resistance value, three-phase synchronization of transformer on-load tap-changers.
-
PT-14 -
Kharkovenergopribor Ltd.
The locator PT-14 is used as an induction signal receiver in a cable tracing and fault location set for the following applications:• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
V‑Series -
Keysight Technologies
The highest real-time oscilloscope measurement accuracy. Keysight uses a proprietary indium phosphide (InP) integrated circuit process to design the key technology blocks to deliver high-bandwidth performance, ultra-low noise, low jitter, and high-voltage signal input. The InP process lets you see your true signal and make the most accurate measurements.
-
T-4 Series -
Picoprobe
T-4 tips are for use in most standard commercial micropositioners for probing integrated circuits, pads, or lines. Each T-4 tip uses the same 10, 22, 35, 60, or 125 micron diameter tungsten wire as our Model 12C Picoprobe, but is mounted to a 0.020 inch diameter, 2 inch long tinned copper shaft.
-
2108 EL -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Four functions : DC current, AC current, AC+DC current, and ACV measurement.● Three input resistance ranges: 1kΩ,1.5kΩ and 2kΩ.● 200uA full scale value.● ±2.5% full scale value accuracy.● Built-in overload protection circuit.● Robust, compact and easy to carry.
-
Gold Box "Infinity" -
Acopian Technical Company
*Highly Configurable, with a seemingly Infinite number of Options*Any slot voltage from 1.5v to 150v is available*Remote Sensing*Open Sense protection*Isolated output*Short circuit and overload protection with enhanced surge capabilities*No minimum load required*Internal EMI Filtering*Pluggable connectors*Can be mounted on two surfaces in any orientation
-
DRK218 -
Shandong Drick Instruments Co., Ltd.
DRK218 breakdown voltage tester is controlled by the computer, through a new smart digital integrated circuits developed by my company and software control system to make the step-up rate is truly uniform, accurate, and be able to accurately measure the leakage current data. Real-time rendering test curve accurate judgment and it can save, analyze and print test data.
-
MCL-400IR+ -
MULTI MEASURING INSTRUMENTS Co., Ltd.
・About Ior Leakage CurrentRecently, the leakage current clamp meter is widely used for insulation control of low voltage circuit as the supplementary method of the insulation resistance measurement. The control of leakage current has the advantages to enable the prediction of insulation condition in the electrical power line without having to shut off the power. The leakage current (Io) includes the capacitive leakage current (Ioc)originated in the capacitance and the resistive leakage current (Ior) originated in the insulation resistance each related to the ground. It is considered that the measurement of resistive leakage current (Ior) is the very useful and effective method for the insulation control of low voltage circuit. However, it was difficult to measure the resistive leakage current (Ior)with traditional leakage current clamp meter. MCL-400IR new digital clamp tester enabled the measurements of the resistive leakage current (Ior)without voltage input(phase detection).